Can You Cut LED Lights? Come to Know – Easy Guide

(Is it possible can you cut led lights by using different techniques? Many LED strips can be cut from the specific part that’s why you need to ensure that you are going to cut it from the pointing spot.)

to add some lightning effects and display a lightning environment, LED light strips are used in various places such as for commercial displays, Home Décor, and DIY projects. A lot of LED lights have very long strips. 

So, to adjust them in an appropriate place, you need to cut them according to the place where you need to install them. but here the question arises; can you cut LED lights? Well, LED Lights are easily cut. Every LED strip Light has copper dots. 

When you cut the LED from these copper ends, all the other LEDs are working properly. Moreover, you can use various types of connectors to connect the cutting ends of the LED light strips. 

How can you cut LED lights without breaking them?

Yes, you can easily cut your LED lights without breaking them. To cut your LED light without any damage you need to find out the cutting marks that are present on the Led Strips. Make sure that you cut the LED light strip by following those marked points to avoid damaging or breaking. 

Where do you need to cut the LED light strip?  

If your LED strip is too long, then we are going to show you the correct way how you can extend the LED strip. Now, the first thing to note about your LED strip is that some cannot be extended because of the power rating there, and if you do try to extend it, you will see the color is consistent. Then, if it has gone too long it might start fading out further along the way. 

• Measure the Length:

When you buy a LED Light strip, it might be too long to adjust it to a specific location. First, you need to measure the area where you are going to install it. after that. Cut the extra led Light. 

Keep in mind that, when you cut the LED Light, cut it into an appropriate place and from the right length. That’s why you first decide how long you need an LED light Strip. 

• Find LED Copper Dots:

You can find out the copper points on the LED strip and further along there are also more copper points. Now, find the point where you would like to cut the LED strip. Moreover, to use the connectors there are 2 more possibilities. 

Additionally, the valid way to cut the LED Strip is to cut it in the middle. Pay your proper attention when you are going to cut it because if you accidentally cut or miss it. You might not get a good connection. 

• Cut the LED Strip:

Now, take a pair of scissors and cut the LED light strip straight from the copper dots. Keep in mind that you cut the LED Strip straight otherwise it will be wasted.  After cutting it you can see a good amount of copper there and you can get good connectivity. 

How Can You Fix Your Cutting LED Light Strip?

We will be going to show you the best methods to join the cutting LED light edges. This method will help you when you try to make a clean and smooth corner. Keep in mind that when you are going to learn and know about whether can you cut LED lights and how they can be fixed, your LED lights will be unplugged when you do this process. 

• Buy a Connector:

First, to join the edges of two LED cutting strips you need a connector. There are a lot of connectors such as T connectors, ribbon-like connectors, hippo connectors, and Straight connectors that are helpful to connect the cutting LED lights. 

• Open the Connector:

Now, to fix the cutting LED lights make sure the connectors are open to expose the pins. Take off the sticky pad that is below the LED Strip. So that you can easily push it into the exact position. 

• Insert the LED light:

After opening the connector, insert the cutting end of the copper LED light strip. Push the LED light strip until the copper is connected to the below silver metal of the connector. 

Make sure that the LED strip is placed under the metal contacts, not on the top of the connector. Do the same with the second end of the cutting LED strips.

• Close the Connectors:

When you place the Cutting Pieces of LED light strips, just push the connector down and you can see it lock into a position. Moreover, if it does not push down easily just take some pliers and use them to lock the ends of connectors.  

Now, you can see the lights of the LED are ON. In that case, if the Lights of LED are not lit up then you might not have a good connection. Try to check your LED strips are in the right position, if it is not then fix them. 

How to reconnect the cutting ends of LED light strips without connectors?

You can easily reconnect your cutting LED light strip with the help of “Soldering”. But you have to be very careful while doing this method because the LEDs are heat sensitive. To complete the process, you need to follow these simple guidelines: 

• Take a Soldering iron. Before using it make sure that the solder applies sufficient heat to melt it.
• First, put some solder on the contact points. 
• Dry it quickly by blowing on it. 
• Then, solder a wire by applying heat for the extension.
• After soldering, ensure that each wire is placed and soldered properly or not. 

Now, your cut LED strip is ready to use without using any connector. Make sure while soldering, you maintain the exact polarity such as you connect the plus point to the plus and minus to the minus point. 

How can you Troubleshoot when your LED light does not light Up? 

Here are some troubleshooting techniques that are helpful for you when your led light does not light up:  

• Make sure that the power supply voltage is compatible with your LED strips. 
• Check your power supply and make sure that they are working properly. 
• Moreover, if your power supply is working properly and your LED is not still Lights up. Then, you need to check other circuit accessories and isolates. 
• Check your other loose connections. 

What are the common mistakes that you need to avoid while cutting the LED strips?

Here we enlist some of the common mistakes that you need to avoid while cutting your LED light Strips:

• Always check that you are not going to cut the LED from the wrong point. 
• Use appropriate tools instead of using improper tools for cutting. 
• Take advice from professional manufacturers. 
• While cutting, don’t apply too much pressure. 
• Handle the LED strip with proper care.

Frequently Asked Questions:

Q. How do LED lights work after you cut them?

When you know about it, can you cut led lights? Then, you cut the LED lights and connect them after cutting by utilizing a connector or Soldering process to make them work again. Simply place the correct sides of LED strips and connect them. Moreover, you can easily connect the LED strip from the different areas of your home. 

Q. Can all LED lights be cut?

A lot of manufacturers and brands point to a specific spot to cut the particular size of the strip. If you don’t find these spots or sections, then check carefully and surely you will find the cutting line or scissors logo that points to the cutting section.  

Q. Will my LEDs still work if I cut them?

To use the cutting LED you need to cut it from the specific section. Many people face an issue that their LED stops working because they cut them from the wrong lines. Moreover, ensure that you cut the strip from where the marked line or scissor logo is. 

Q. Can you fix LED strip lights if you cut them?

Yes, you can fix your LED lights before cutting them. You can use soldering techniques and connectors to fix them. Moreover, if your LED stops working after you cut it. Then, it means your LED is designed in a way that is not for cutting or you might cut it to the wrong place. 

Finishing:

Before you are going to buy LED lights you need to decide which type of LED light you are going to use such as RGB strip, White LED, and RGBW lights. You can use these LED lights to decorate your home or kitchen. These colorful lights will offer brightness with colors in dark spaces. 

A lot of LED lights are very long. That’s why you need to cut it to fix them in a specific area. Don’t worry about how can you cut LED lights because you can easily cut it and connect it by utilizing a connector or Soldering techniques. 

for more information visit voxblend.com